Prepare the SMP/E Environment for a Pax Installation

The following steps describe the process to install products using native SMP/E JCL:
ce18
The following steps describe the process to install products using native SMP/E JCL:
  1. Allocate product data sets and SMP/E data sets.
  2. Create an SMP/E environment.
  3. Receive base functions.
  4. Download and RECEIVE PTFs from the Broadcom Support Download Center.
  5. Run an SMP/E APPLY CHECK operation.
  6. Apply base functions using SELECT GROUPEXTEND.
  7. Run an SMP/E ACCEPT CHECK operation.
  8. Accept base functions using SELECT GROUPEXTEND.
  9. Download external HOLDDATA.
  10. Configure the product according to your site requirements.
The members that are used in this procedure prepare the data sets, initialize the zones, and create the DDDEFs for your product.
For information about the members, see the JCL comments.
 
Follow these steps:
 
  1. Customize the macro SCMSEDIT with your site-specific information and then copy the macro to your SYSPROC location. Replace the rightmost parameters for each ISREDIT CHANGE command. When you edit an installation member, type SCMSEDIT on the command line, and press Enter to replace the defaults with your specifications.
    The macro is ready to customize the 
    yourHLQ
    .SAMPJCL members.
     Set the PRODHLQ to the same value specified for 
    yourHLQ
     within the JCL that is used to unzip the pax file.
     The following steps include instructions to execute the SCMSEDIT macro each time you open a new SAMPJCL member. To edit all SAMPJCL members simultaneously, read and follow the instructions in the SCMAREAD member, and submit the SCMEDALL member.
  2. Open the SAMPJCL member SCM00ALL in an edit session and execute the SCMSEDIT macro from the command line.
    SCM00ALL is customized.
  3. Submit SCM00ALL.
    This job produces the following results:
    • The target and distribution data sets for your product are created.
    • Unique SMPLTS, SMPMTS, SMPSCDS, and SMPSTS data sets for this target zone are created.
  4. (Optional) If your product requires a USS file system or if you want to install a feature of the product that requires a USS file system, allocate and mount the file system:
    1. Open the SAMPJCL member 
      SCM
      03ALU in an edit session and execute the SCMSEDIT macro from the command line.
       
       
      SCM
      03ALU is customized.
    2. Submit 
      SCM
      03ALU.
      This job allocates your zFS data sets.
    3. Open the SAMPJCL member 
      SCM
      06MKD in an edit session and execute the SCMSEDIT macro from the command line.
      SCM
      06MKD is customized.
    4. Submit 
      SCM
      06MKD.
      This job creates all directories and mounts the file system.
  5. Open the SAMPJCL member SCM10CSI in an edit session and execute the SCMSEDIT macro from the command line.
    SCM10CSI is customized.
  6. Submit SCM10CSI.
    This job produces the following results:
    • The CSI data set is defined.
    • The SMPPTS and SMPLOG data sets are allocated.
    • The global, target, and distribution zones are initialized.
    • The DDDEF entries for your product are created.
    • The DDDEFs for the required SMP/E data sets are created.
  7. (Optional) If your product requires zFS or if you want to install a feature of the product that requires zFS, add the DDDEFS that are required for the file system to your SMP/E environment:
    1. Open the SAMPJCL member 
      SCM
      15CSU in an edit session and execute the SCMSEDIT macro from the command line.
      SCM
      15CSU is customized.
    2. Submit 
      SCM
      15CSU.
      This job customizes the CSI by adding the DDDEFs associated with the directory.