TMSCTLG Messages

This section contains the TMSCTLG Messages.
ca1tms
This section contains the TMSCTLG Messages.
**** AUDIT DATA SET IS PAST THRESHOLD ******** RE-RUN JOB AFTER BACKING-UP TMC ****
Reason:
The threshold value of the Audit data set has been exceeded.
Action:
Execute TMSCOPY to back up the TMC and Audit data set, and resubmit the job.
 
**** WARNING IDCAMS DD SUPPLIED BUT NO DATA WAS SELECTED AS INPUTTO THE SORT
Reason:
The IDCAMS DD was provided but no tape data sets with a file sequence of 1 were found within the IDCAMS data set.
Action:
If the system running TMSCTLG has access to all catalogs to which tape data sets are cataloged, no action is required. However, if the system does not have access to all catalogs, review the expired catalog listing for expiration of cataloged tape data sets. See the JCL example for correct syntax and use TMSUPDTE, TMSUDSNB or
CA 1
online facilities to update the EXPDT in these records to CATALOG. This
must
be done prior to running TMSCLEAN to prevent premature scratching of volumes.
 
**** WARNING IEHLIST DD SUPPLIED BUT NO DATA WAS SELECTED AS INPUTTO THE SORT
Reason:
The IEHLIST DD was provided but no tape data sets with a file sequence of 1 were found within the IEHLIST data set.
Action:
If the system running TMSCTLG has LOCATE access to all catalogs to which tape data sets are cataloged, no action is required. However, if the system does not have access to all catalogs, review the expired catalog listing for expiration of cataloged tape data sets. See the JCL example for correct syntax, and use TMSUPDTE, TMSUDSNB or
CA 1
online facilities to update the EXPDT in these records to CATALOG. This
must
be done prior to running TMSCLEAN to prevent premature scratching of volumes.
 
**** WARNING NO TMC RECORDS SELECTED
Reason:
No Volume records with an EXPDT=CATALOG and VOLSEQ=1 were found on the TMC.
Action:
None. This is an informational message.
 
BAD CREATE DATE
Reason:
The CDATE (creation date) for this volume is 0.
Action:
The volume is not expired by TMSCTLG. Update the CDATE for this volume.
 
Bad EXPDT for VOLSER=vvvvvv error: FDBK=0 INVALID DATE 
Reason
:
The EXPDT for volume vvvvvv is not valid.
Action:
Manually update the EXPDT using the ISPF interface to a valid value.
BAD MVP 1SVOL=vvvvvv
Reason:
A multivolume chain under Catalog Control contains a Volume record which has one of the following errors:
(*** Error: no level 15 lists allowed. ***)
The NEXTVOL of vvvvvv is not defined in the volume ranges of TMC Control records #1 and #3.
(*** Error: no level 15 lists allowed. ***)
The PREVVOL of this volume is not equal to the volser of volume vvvvvv.
(*** Error: no level 15 lists allowed. ***)
The current volume's VOLSEQ is not equal to VOLSEQ + 1 of volume vvvvvv.
Action:
Execute TMSPTRS to analyze the chains in the TMC, and correct any reported errors.
 
EXPDT=xxxxxxxxxx
Reason:
The volume is removed from Catalog Control. The date value expressed by xxxxxxxxxx, rather than the normal expiration (run date plus R9 extension), is used. The value of xxxxxxxxxx is the highest expiration date found on the DSNB chain.
Action:
None. This is an informational message.
 
LOCATE ERROR-xx
Reason:
TMSCTLG is unable to determine the catalog status of this data set. The specified CVOL return code or VSAM/ICF reason code is from the LOCATE macro. These data sets are not expired until corrective action is taken.
Action:
To determine the cause of the LOCATE error, see
IBM MVS Catalog Administrating
 Manual
.
 
Lookup Error: VOL=vvvvvv FSQ=nn VSQ=n DSN=dsname RC=4 RSN=36FDBK=4 LOCATE FOR DSN FAILED IN LOCATE/CATALOG INTERFACE
Reason:
Catalogs are either offline or the DSN being expired by catalog control is for a GDG base not a specific generation of the base.
Action:
No action is required. This is an informative message. TMSCTLG will not expire data sets.
 
Lookup Error: VOL=vvvvvv FSQ=nn VSQ=n DSN=dsname RC=0 RSN=0FDBK=5 1STVOL DOES NOT MATCH
Reason:
The listed data set was found in the OS catalog, however, the volume serial number it is cataloged to does not match the volume serial number of the TMC record.
Action:
No action is required. This is an informative message. TMSCTLG treats the TMC data set as an MVS catalog error and thus expires it.
 
Lookup Error: VOL=vvvvvv FSQ=nn VSQ=n DSN=dsname RC=0 RSN=0FDBK=7 FILESEQ DOES NOT MATCH
Reason:
The listed data set was found in the OS catalog. However, the fileseq in the catalog does not match what is in the record.
Action:
None. This is an informational message. TMSCTLG treats the TMC data set as an MVS catalog error and expires it.
  
GETVOL error: VOL=xxxxxx BASE=yyyyyy FDBK=n
Reason:
The volser xxxxxx could not be read or is not defined in the TMC. A pointer to this bad volser was found in base-volser yyyyyy or in a volume chained to base-volser yyyyyy. 
Action:
Recommend running TMSPTRS to find all chaining errors. In particular, correct the error associated with the multi-volume chain starting on volume yyyyyy.
 
GETDSNB_ENQ error: DSNB#=nnnnnnnn, BASE=yyyyyy FDBK=z
Reason:
The DSNB nnnnnnnn could not be read or updated. Most likely it is an invalid value and is either pointed to by base-volser yyyyyy or chained to a valid DSNB that itself is chained to base-volser yyyyyy.
Action:
Recommend running TMSPTRS to find all chaining errors. In particular, correct the error associated with the multi-file chain starting on volume yyyyyy.